High data transmission rates are becoming very crucial. More and more organizations are opting for the options that can improve their network infrastructure. The quality of the cable affects the signal transmission rates and the way they are installed. The installation team usually makes certain mistakes that lead to network failure. Experts help organizations install structured cables to get their desired results and data transmission speed.
Here in this article, we will discuss some of the common dos and don’ts of network cable installation to get better results.
Common Dos for cable installation
To get optimum results, network cable users have to follow certain principles. Some of the important factors that you must follow while installing the cables are as follows.
1. Cable storage
Network cables are not easy to buy due to their high cost. It is always necessary to keep the wires in a safe place when you buy them. Please keep them in a cool, dry place so that you can get better results through the optimum signal transmission. It is dangerous for your cables to get wet or come in contact with water. Please place them in a safe place certain feet above the ground level to ensure they don’t get damaged before installation.
2. Right cable selection
You are investing a huge amount in making your network infrastructure better. Please do not make a mistake in buying and installing the wrong cable as installing and replacing the network cables with new ones is not an easy job. First, identify your need and the distance you want to send the signal, and then decide on the cable selection. Hire structured cabling UAE firms and companies to help you identify the right type of network cable for your need.
3. Label the cables
Installation of network cables is a hard nut to crack. You are playing with several wires at a time. In such situations, the chances of getting confused are higher. It is always recommended to label your network cables, not to mix the wires. The management of the labeled cables becomes easier and the time to install labeled lines is lower.
4. Clean the connectors
Connectors are an important part of the network cables. They are used to connect the wires to the device or other wires. Some people complain that they are not getting the required results despite using the latest and expensive network cables. It is because of the mistakes they make while attaching the connectors. The installation team ignores the connectors’ cleanliness, and dirty connectors always result in signal attenuation and dB loss fiber optic problems.
5. Dust caps around the cables
You must keep in mind while installing the network cables that cover the open ends of the wires with the dust caps. It will keep your cables safe from damage, and the results of signal transmission will be better. Damaged cords are of no use, so it is better to spend some money and buy dust caps for your wires to protect them from dirt.
6. Test the cables
Before you lay, the network cables do test your lines if they are performing well or not. You can test the wires in-field or get pre-tested cables. It depends on you that either you want to buy pre-tested wires or not. But make sure to try the lines before installation.
7. Consider future needs
The network cables and their types are evolving with each passing day. One must take into account future needs. Install your wires so that they are easy to remove and replace by other and latest cables without damaging the network infrastructure. some of the brief guides about fixing cut fiber optics cable while installation
Common Don’ts of cable installation
The Don’ts of network cable installation is equally important as the Dos of the installation. Below are some of the most common don’ts of cable installation that one must follow.
1. Don’t pull the cable jacket carelessly
In the installation, the installation team must deal with the cables gently. Sometimes while removing the wire jacket, the line itself gets damage. Remove the jacket with the right tool and without exerting extra pressure on them.
2. Don’t heat the cable racks
Do not overload the cable racks. Storing numbers of cables can heat the cable rack, which is not a good thing. It is dangerous for your network infrastructure, and the results you will get will not be satisfactory. Also, please do not keep the wires too tightly; it minimizes the network quality. Use cable ties to keep the wires intact and avoid them spreading all over the place.
3. Don’t let cables to contact with ceiling or the floor
You may have to lay the cables through the walls and ceiling. You must make sure that they do not contact the wall, floor or ceiling. Hire the best installation team to do the job for you. You can acquire structured cabling UAE companies’ services to help you install the cables with all the precautionary measures.
Strengthen your network infrastructure today
If you haven’t opted for the latest structured cables for your network infrastructure, then you must join today. Strengthen your network infrastructure and improve signal transmission rates. Take care of the aspects that one must consider while the cable installation. Ask for expert help to install the network cable of any type.